R-300
The R-300 Roll-On Conveyor applies decorative foil to flat surfaces on a variety of substrates. The roller height is adjustable to accommodate stamping different parts.
The R-300 and CPS Resource, Inc. Conveyor Line of equipment effortlessly decorates a wide range of substrates. Some of those substrates include: leather, vinyl, plastics and wood.
STANDARD FEATURES
- Ground steel side frames with welded steel support frame, casters and leveling screws
- Roller assembly guided by 4 hardened steel shafts and 8 ball bushings
- Threaded adjustment to tilt roller assembly to level roller to part
- Adjustable stamping height with easy to adjust crank handle for stamping different size parts
- Adjustable part guide
- Roller assembly is spring loaded making it possible to stamp slightly curved parts
- Ceramic heaters for quick heat recovery
- Non-contact infrared temperature sensor
- Quick change roller design
- 4″ bore x 2″ stroke double acting rod end cylinder with fine tuning roller stamping depth stop and flow controls
- Air safety shut off valve to keep roller from falling if air pressure is lost • Filter, regulator and automatic lubricator
- Tool Kit
ELECTRICAL CONTROLS
- Proportioning temperature control with digital display
- Power on, heaters on, foil on, roller motor on, conveyor on and conveyor manual auto switches
- Start, stop and foil advance buttons
- Variable speed stamping control
- Variable speed waste foil take-up system with variable tension adjustment
SPECIFICATIONS
R-200 Conveyor Roll-On
| Max Stamping Pressure | 250 Kgf / cm2 / 500 PSI |
| Stamping Roller Size | 58.5 x 125 x 200mm
2.30″ x 5″ x 8″ |
| Stamping Roller Stroke | 40-60mm / 1.5″x 2.25″ |
| Head Adjusting Distance | 0-150mm / 0-6″ |
| Conveyor Width | 220mm / 8.66″ |
| Conveyor Length | 1200mm / 48″ |
| Max Foil Width | 220mm / 8.66″ |
| Heaters | 220 V x 500 watts, 6 each |
| Machine Weight | 550 Kg/1200 lb. |
| Voltage Required | 220 V x Single Phase x 60 Hz |
| Machine Size (W,L,H) | 1000x700x1600mm 39″x27″x62″ |
| Stamping speed/sec | 0-150mm/0-6″ |
| Air Supply | 5-6 Bar / 70-90 PSI |
R-300 Conveyor Roll-On
| Max Stamping Pressure | 250 Kgf / cm2 / 500 PSI |
| Stamping Roller Size | 58.5 x 125 x 300mm
2.30″ x 5″ x 12″ |
| Stamping Roller Stroke | 40-60mm / 1.5″x 2.25″ |
| Head Adjusting Distance | 0-150mm / 0-6″ |
| Conveyor Width | 320mm / 12.5″ |
| Conveyor Length | 1200mm / 48″ |
| Max Foil Width | 320mm / 12.5″ |
| Heaters | 220 V x 500 watts, 6 each |
| Machine Weight | 550 Kg/1200 lb. |
| Voltage Required | 220 V x Single Phase x 60 Hz |
| Machine Size (W,L,H) | 1000x700x1600mm
39″x27″x62″ |
| Stamping speed/sec | 0-150mm/0-6″ |
| Air Supply | 5-6 Bar / 70-90 PSI |
| Back to Top |
Model R-1200
More Information
This 48″ Roll-On machine can apply decorative foils to large flat surfaces up to 48″ wide and from 1/8″ to 6″ thick. The R-1200 and CPS Conveyor Line of equipment effortlessly decorates a wide range of substrates. Some of those substrates include: leather, vinyl, plastics and wood.
STANDARD FEATURES
- Welded steel support frame with casters and leveling screws
- 48″ wide x 48″ long conveyor
- Adjustable stamping height for foiling different height parts
- 8″ diameter silicone roller
- Ceramic heaters for quick heat recovery
- Non-contact infrared temperature sensor
- (2) 6″ bore cylinders for consistent stamping pressure on the roller
- Filter, regulator and automatic lubricator
- Proportioning temperature control with digital display
- Infrared non-contact temperature sensor
ELECTRICAL CONTROLS
- Power on, heaters on, variable speed stamping control, variable speed foil control
- 4 Emergency stop buttons, on each corner of machine
SPECIFICATIONS
| Max Stamping Pressure | 6 ton |
| Head Stroke | 50mm |
| Conveyor Speed | 7-12 m/min |
| Stamping width | Max 1220mm |
| Stamping Roller | 200 x 1240mm |
| Voltage Required | 220 V x Three Phase |
| Machine Weight | 1500 Kg |
| Machine Size (W,L,H) | 1325x1410x1959mm |
| Air Pressure | 5-6 Kgf/cm2 |
| Power Rating | 7.5 Kw |
| Back to Top |
Model R-070 Vertical Roll
More Information
The R-070 Vertical Roll-On machine is used to decorate 360° around cylindrical parts such as cosmetic cases, cups, flower pots and other similar parts.
Model R-070 Rotary Index Table
The Rotary Index Table, shown at the left, is an optional feature that can be used for increased production.
STANDARD FEATURES
- Ground steel side frames with welded steel tubing support frame with casters and leveling feet
- Adjustable stamping height with easy to adjust crank handle
- Roller assembly guided by 2 hardened steel shafts and ball bushings
- Fine thread tilt adjustment to level roller to part
- Ceramic heaters for quick heat recovery
- Non-contact infrared temperature sensor
- Quick change roller design
- 2.5″ bore x 2.5″ stroke double acting double rod end cylinder with fine tuning roller stamping depth adjustment stop and flow controls
- Filter, regulator and automatic lubricator
- Tool kit
ELECTRICAL CONTROLS
- Proportioning temperature control with digital display
- Dwell, foil start and foil stop timers
- Part counter and stop button
- Power on, heaters on, tension on and set-up run switch
- Adjustable stamping and foil pull speed
OPTIONS
• Multicolor heat transfer indexing system with dual photo eye registration with easy to adjust left to right and front to back transfer placement
• Tooling fixtures
• Rotary indexing tables
• Auto eject systems
• Fully automated systems
• Pneumatic powered slide tables
• Automatic feed bowls
• XYR tables
SPECIFICATIONS
| Max Stamping Pressure | 180 Kg / 1/4 Ton |
| Stamping Roller Size | 58.5x125x70mm/2.30″x5″x3″ |
| Stamping Roller Stroke | 63mm/2.25″ |
| Roller Height Adjustment | 0-200mm/0-8″ |
| Max Foil Width | 0-100mm/0-4″ |
| Heaters | 220V x 500 watts, 3 each |
| Voltage Required | 220 V, Single phase, 60 Hz |
| Machine Weight | 450 Kg/850 lbs. |
| Machine Size (LxWxH) | 750x700x1750mm/30″x27″x690″ |
| Air Supply | 5-6 Bar/70-90 PSI |
| Back to Top |
Model R-070 Auto Pen
More Information
The R-070 Automatic Pen machine applies hot stamp foil and heat transfers to pen barrels and pen caps. The R-070 Model is also available as an Automatic Pencil machine which decorates pencils with hot stamp foil and heat transfers.
R-070 Automatic Feed System
This machine has a production rate of 25 Pens each per minute.
STANDARD FEATURES
- Side frames constructed of ground steel with welded steel support frame, casters and leveling feet
- All manufactured components are chrome plated and painted steel
- Roller assembly guided by 4 hardened steel shafts and 8 ball bushings
- Threaded adjustment to tilt roller assembly to level roller to part
- Adjustable stamping height with easy to adjust crank handle for stamping different size parts
- Air over hydraulic slide table for smooth actuation while part is being stamped
- Large table for mounting tooling fixtures
- Adjustable stamping speed control
- Ceramic heaters for quick heat recovery
- Non-contact infrared temperature sensor
- Quick change roller design
- 4″ bore x 3″ stroke double acting double rod end cylinder with fine tuning roller stamping depth stop and flow controls
- Air safety shut off valve to keep roller from falling if air pressure is lost
- Filter, regulator and automatic lubricator
- Three sided plexiglas guarding with photo electric light curtain across front of machine for operator safety
- Tool kit
ELECTRICAL CONTROLS
- Proportioning temperature control with digital display
- Dwell, foil start and foil stop timers
- Total part counter
- Variable speed electrical tension control with variable tension adjustment to keep slack out of foil or transfer while part is being stamped
- Manual and automatic controls
- Power on, heaters on, tension on, roller motor on, table on, stamping mode manual-auto and foil or heat transfer switch
- Start, stop, foil-transfer advance, table forward and table reverse buttons
- Variable foil and tension speed controls
- Multi-color heat transfer indexing system with dual photo eye registration with easy to adjust left to right and front to back transfer placement
- Photo electric safety light curtain across front of machine
SPECIFICATIONS
| MODEL R-070 AUTO PENCIL | |
| Max Stamping Pressure | 180 Kg / 400lb. |
| Stamping Roller Size | 58.5x125x200mm/2.30″x5″x8″ |
| Stamping Roller Stroke | 40-60 mm / 1.5 x 2.25″ |
| Head Adjusting Distance | 0-50 mm / 0-2″ |
| Conveyor Width | 200mm / 8″ |
| Conveyor Length | 520mm / 20.5″ |
| Maximum Foil Width | 200mm / 8″ |
| Heaters | 220 V x 500 watts, 4 each |
| Voltage Required | 220 V, Single Phase, 60 Hz |
| Machine Weight | 550 Kg / 1215 lbs. |
| Machine Size | 750x800x1960mm / 30″x32″x77″ |
| Production Rate | 25 each / min. |
| Air Supply | 5-6 Bar / 70-90 PSI |
| MODEL R-070 AUTO PEN | |
| Max Stamping Pressure | 250 Kg / cm2 / 500lb. |
| Stamping Roller Size | 58.5x125x100mm/2.30″x5″x4″ |
| Stamping Roller Stroke | 40-60 mm / 1.5 x 2.25″ |
| Head Adjusting Distance | 0-100 mm / 0-4″ |
| Conveyor Width | 140mm / 5.5″ |
| Conveyor Length | 520mm / 20.5″ |
| Maximum Foil Width | 100mm / 4″ |
| Heaters | 220 V x 500 watts, 3 each |
| Voltage Required | 220 V, Single Phase, 60 Hz |
| Machine Weight | 550 Kg / 1100 lbs. |
| Machine Size | 1225x1226x1875mm / 49″x50″x75″ |
| Production Rate | 25 -30 each / min. |
| Air Supply | 5-6 Bar / 70-90 PSI |
| Back to Top |
Model DRT-200
More Information
This machine is used primarily to apply Foil or Heat Transfers to elongated parts. The operation of the DRT-200 eliminates air entrapment during the foiling process.
Model DRT-200 Control Panel
Pictured is the manual control panel of the DRT-200. The manual controls allow step by step operation for part placement and set-up.
Applications
The DRT-200 is ideal for:
- Applying Heat Transfers with eyemark registration to flat surfaces up to 18 inches in length
- A wide range of Hot Stamp Foil applications
STANDARD FEATURES
- Side frames constructed of ground steel with welded steel support frame, casters and leveling feet
- All manufactured components are chrome plated and painted steel
- Roller assembly guided by 4 hardened steel shafts and 8 ball bushings
- Threaded adjustment to tilt roller assembly to level roller to part
- Adjustable stamping height with easy to adjust crank handle for stamping different size parts
- Air over hydraulic slide table for smooth actuation while part is being stamped
- Large table for mounting tooling fixtures
- Adjustable stamping speed control
- Ceramic heaters for quick heat recovery
- Non-contact infrared temperature sensor
- Quick change roller design
- 4″ bore x 3″ stroke double acting double rod end cylinder with fine tuning roller stamping depth stop and flow controls
- Air safety shut off valve to keep roller from falling if air pressure is lost
- Filter, regulator and automatic lubricator
- Three sided plexiglas guarding with photo electric light curtain across front of machine for operator safety
- Tool kit
ELECTRICAL CONTROLS
- Proportioning temperature control with digital display
- Dwell, foil start and foil stop timers
- Total part counter
- Variable speed electrical tension control with variable tension adjustment to keep slack out of foil or transfer while part is being stamped
- Manual and automatic controls
- Power on, heaters on, tension on, roller motor on, table on, stamping mode manual-auto and foil or heat transfer switch
- Start, stop, foil-transfer advance, table forward and table reverse buttons
- Variable foil and tension speed controls
- Multi-color heat transfer indexing system with dual photo eye registration with easy to adjust left to right and front to back transfer placement
- Photo electric safety light curtain across front of machine
SPECIFICATIONS
| Max Stamping Pressure | 250 Kg / 500lb. |
| Stamping Roller Size | 58.5x125x200mm / 2.30″x5″x8″ |
| Stamping Head Stroke | 0-75 mm / 0-3″ |
| Head Adjusting Distance | 0-150 mm |
| Table Stroke | 0-850mm / 0-33″ |
| Possible Stamping Size (W,L,H) | 200x700x550mm / 8″x27.5″x21″ |
| Actual Output pcs/hour | 150-250 each / hour |
| Maximum Foil Width | 200mm / 8″ |
| Foil Feed Distance | 0-750mm / 0-30″ |
| Heaters | Ceramic 500 watts, 6 each |
| Voltage Required | 220 V, Single phase, 60 Hz |
| Machine Weight | 850 Kg / 1875 lbs. |
| Machine Size | 1800x700x2050mm / 70″x27″x80″ |
| Air Supply | 5-6 Bar / 70-90 PSI |
| Back to Top |
VROWB06 Water Bottle
- Mandrel supported. A simple mandrel fixture supports the water bottle while the heat transfer is being applied. This eliminates the need to inject air in the bottle which has the following advantages: a) decreased cycle time, b) eliminates contamination from air inside the bottle.
- Air injected. Injects air into the water bottle in order to release the heat transfer design.