Model DR-1
More Information
Stamping in-line with extruder or with drive system, DR-1 has the ability to hand feed pre-cut lengths and decorate on angles of 0° to 180°.
DR-1 Rotation Section
- Motor driven off-line applications
- Equipment rotation up to 180°
- Variable speed drive system for stand alone operation for foiling pre-cut lengths of material
Drive System includes:
- Line speed meter
- RPM meter
- Adjustable tension control
- Variable stamping speed control
- Motor on-off switch
- Modular units can be positioned in-line for multiple head applications
STANDARD FEATURES
- Pivoting frame constructed of ground chrome plated steel with geared pivoting mechanical mechanism with crank handle
- Welded steel support frame with casters and leveling feet
- All manufactured machine parts are chrome plated and painted steel
- Roller assembly guided by 2 hardened shafts and ball bushings
- Fine thread tilt adjustment on roller assembly
- Chrome plated back-up roller
- Fine thread adjustment on roller assembly for precise placement of roller to part, front to back
- 5 sets of rollers to guide and support part while being stamped
- Filter, regulator and automatic lubricator
- 2.5″ x 4″ stroke double acting cylinder with fine tuning roller stamping depth adjustment and flow controls
- 8″ diameter x 2″ wide silicone roller
- Proportioning temperature control with digital display
- Infrared non-contact temperature sensor
- Variable speed waste foil take-up system with variable tension adjustment
- Power on, start, stop, foil on, motor on, heater on and foil speed controls
SPECIFICATIONS
Max Stamping Pressure | 150 Kg/cm2 | |
Max Stamping Width | 90mm |
Stamping Head Stroke | 50-50mm |
Heaters | 220 V x 800 watts, 2 each |
Voltage Required | 220 V x Single Phase x 60 Hz |
Amount of Head Swivel | 0″-180″ |
Stamping Speed | 2-20 m/min |
Machine Weight | 450 Kg |
Machine Size (W,L,H) | 700x750x1600mm | DR1 Control Panel |
Air Supply | 5-6 Bar |
| Back to Top |
Model DM-1
More Information
The DM-1 fixed head is used in-line with extruder for foiling the top side of profiles
Applications
- Picture Frames
- Vertical Blinds
- Trophy Columns
- Extruded Profiles
STANDARD FEATURES
- Ground steel side frames with welded steel support frame, casters and leveling feet
- Adjustable stamping height with easy to adjust crank handle for stamping different size parts
- All manufactured machine parts are chrome plated and painted steel
- Roller assembly guided by 2 hardened shafts and ball bushings
- Fine thread tilt adjustment to level roller to part
- 5 se
ts of rollers to guide and support part while being stamped - 8″ diameter x 3″ wide stamping roller
- Non-contact infrared temperature sensor
- 2.5″ x 2″ stroke double acting rod end cylinder with fine thread stamping roller depth stop adjustment and flow controls
- Filter, regulator and automatic lubricator
- Tool kit
ELECTRICAL CONTROLS
- Proportioning temperature control with digital display
- Variable speed waste foil take-up system with variable tension adjustment
- Power on, foil on, roller motor on, heaters on, start, stop, foil speed and foil advance controls
SPECIFICATIONS
Max Stamping Width | 90mm / 3-1/2″ |
Stroke of Stamping Wheel | 0-50mm / 0-2″ |
Voltage Required | 220 V x Single Phase x 60 Hz |
Air Supply | 5-6 Bars / 70-90 PSI |
Heater | 220 V x 1000 watts, 2 each |
Consumption of Electrical Power | 3 Kw / hr |
Machine Size (W,L,H) | 700x750x1600mm |
Machine Weight | 450 Kg |
| Back to Top |